SP.D PSG
STANDARD SET-UP:
- Hot galvanized frame
- Polyethylene cistern
- Fixed rudder adjustable in length
- Axle with registerable roadway
- High wheels with narrow cross-section
- Access ladder
- Diaphragm pump
- 5-way electrical controls more on/off general, electrical pressure regulation, supply filter, remote control panel in the cab with isometric gauge Ø 63
- Additional isometric pressure gauge Ø 100
- External beam choice presser with contenitori washers
- Panel with centralized controls from the ground placed on the side of the pulverizer
- External intake filter with check valve
- Three-way diverter for filling
- Dry external tank level
- Hydraulic agitation of the liquid in the tank
- Hand washer tank
- Circuit washing device even with the full tank
- Side tank discharge with valve
- Hydraulic boom "PRESTIGE"
HYDRAULIC WEEDING BAR "PRESTIGE" 12,14 and 15 m:
- Two pistons for general opening and closing
— Sequential section movements (such as a four-piston bar)
- Galvanized frame
- Hub of the external sections with anti-urto spring
- Full protection of jets
- Mechanical balancer
- Stainless steel casting rods
- Jets with membrane anti-drip
- Fan nozzles made of synthetic material
- Hydraulic tubes with quick attachment to the hydraulic sockets of the tractor
PUMPS AVAILABLE
LOW PRESSURE COMET: BP 125, BP 171, BP 281
ANNOVI REVERBERI LOW PRESSURE: AR 135, AR 160, AR 280
Specifications
- Polyethylene tank with capacity from 2000 to 3000 liters.
- Low diaphragm pressure pump for the calibrated distribution of products.
- Volumetric control group with exhaust regulators.
Rules
All pulverisers comply with EC regulations on safety and health protection; they also comply with other European standards on safety and environmental protection.
Cistern
- Actual capacity 5% higher than nominal capacity.
- Quantity of residual liquid in a flat position and with an inclination of ±10% below the limits provided for by current regulations.
Pumps
Features of available pumps:
- Low pressure membrane, flow rated from 160 to 280 liters/minute, maximum pressure 20 bar.
TYPE | SP.D 2000 (SENZA BARRA) | SP.D 2500 (SENZA BARRA) | SP.D 3000 (SENZA BARRA) |
| Length, cm | 430 | 430 | 430 |
| Width, cm | 150 | 150 | 150 |
| Height, cm | 190 | 210 | 295 |
| Tank capacity liters | 2120 | 2640 | 3160 |
Specifications may be altered without notice
*weights vary depending staging
SP.D 2500 LT BARRA PRESTIGE 18 MT
SP.D PSG 2000 LT BARRA 15 MT
SP.D PSG 2000 LT BARRA 15 MT
Optional
Brass single-jet add-on, on a 15 m bar
Brass double-jet add-on, on a 15 m bar
Brass double-jet add-on, on a 14 m bar
Brass double-jet add-on, on a 12 m bar
Remote control add-on for Bravo series computers + 5-year subscription package + GPS
Surcharge for sprayers SP.D 3000 approved road use in Italy with no load (Italy only)
Toolbox
Delta 70 monitor for ISOBUS connection complete with SMART 2 cables and antenna
7-way oil and 5-way water keypad kit to be connected to the ISOBUS computer
7-way electric control unit for ISOBUS connection
5-way electric control unit for ISOBUS connection
Support for 5 meters of Floris model tank loading hose
Signal light system kit
Hydraulic lift to adjust hydraulic boom height H 1100
GPS speed sensor
Five sections product automatic distribution computer. Information displayed: Application Rate, Speed, Pressure, Flow rate, Sprayed quantity, Tank level, Area covered, Spraying duration, Distance covered
Series 350 computer with 5 section electric controls for product distribution, electro-hydraulic controls of boom movements, on SP.D sprayers: Computer BRAVO 350S for automatic distribution of the product in five sections and up to seven oil ways
400S LT series computer for product distribution, 5-section electric controls, GPS satellite guidance for distribution tracking.
NAVIGATOR LT GPS navigator for distribution precision tracking, on sprayer P.PR and SP.D.
Foam marker mounted on field sprayer
Kit of hydraulic pump, oil tank and filter for field sprayers with pumps BP 171 or AR 160
Electro-hydraulic control with 3 movements for hydraulic booms with cross closing equipped with a hydraulic lift or inclination corrector
Electro-hydraulic control with 4 movements for hydraulic booms with cross closing equipped with a hydraulic lift and inclination corrector
H 1000 hydraulic lifter with air suspension
Hydraulic inclination corrector piston on self-levelling system
Two side terminals with nozzle for boom extension of 1 metre (where application is possible)
Articulated drawbar with pump support, approved for road use in Italy
Articulated drawbar with pump support and with locking piston approved for road use in Italy
Articulated drawbar with tractor arms coupling and pump support, for sprayers SP.D
Intake device for chemical products
Filling hose with “T” filter, connection to the suction filter and non-return valve
Floating tank filling filter complete with hose
Centrifugal pump with hydraulic motor and hose for tank filling
Electronic flowmeter for tank filling
Rotating nozzle with tank washing jet
Kit of 5 plastic filters on boom sections
Pair of mudguards for sprayer SP.D
Surcharge for wheels 230/95R44 on sprayers SP.D 1500 and 2000
Surcharge for wheels 270/95R44 on sprayers SP.D 2500 and 3000
Cardan joint 40 hp with guard
Cardan joint 50 hp with guard
Constant-velocity (wide-angle) cardan joint 40 hp with guard
Constant-velocity (wide-angle) cardan joint 60 hp with guard

